Tháp Mạch SpeedyBee F405 V5 OX32 55A 30×30 Stack

2,350,000₫

Danh mục: , ,
Mô tả

 

F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
F405 V5 OX32 55A
Specifications
Product Name SpeedyBee F405 V5 30.5×30.5mm Model Aircraft Flight Controller
MCU STM32F405
IMU (Gyro) ICM42688P
USB Port Type New Type-C interface
Barometer SPA06-003
OSD Chip AT7456E
Full-featured Bluetooth Tuning Supported. Connect via SpeedyBee App for FC firmware flashing and parameter tuning.
Wireless FC Firmware Upgrade Supported
DJI Air Unit Connection Supports 6-pin direct plug-in or solder connection
Blackbox Supported, built-in 16MB storage chip
Input Voltage 3-6S LiPo battery
Independent 5V BEC Output 9 groups (4× +5V pads on front, 1× BZ+ buzzer pad, and 4× +5V pads at the corners for external LEDs). Total output current: 1.5A.
Independent 9V BEC Output 2 groups (1x 9V pad on front, 1x 9V output in a connector on the back). Total output current: 3A. Supports PINIO remote on/off control.
MCU & Gyro Power Independent LDO
3.3V Output 1 group (1× 3.3V pad on front)
4.5V Output 3 groups (3× 4.5V pads on front). Can power receiver and GPS when FC is powered via USB. Max output current: 1A.
ESC Signal M1-M4 pads and 10-pin connector on the back
Servo Signal S5-S6 pads on the front
ESC Telemetry Input Supported (UART5)
Betaflight Camera Tuning Pad Supported (CC pad on front)
I2C Supported (GPS connector + pads)
UART UART1 (Bluetooth); UART2 (front pads for receiver); UART3 (DJI VTX pads + rear SH1.0-6-pin); UART4 (GPS pads + front SH1.0-6-pin); UART5 (TLM); UART6 (receiver pads + rear SH1.0-4-pin)
ST LED Pads Supported, on front G/5V/LED pads; controlled by FC firmware
Meteor LED Strip Pads Supported. Switch between SB-LED and ST-LED modes via BOOT button or App. In SB-LED mode, controlled by ESP32 Bluetooth chip.
Buzzer Pads Supported
BOOT Button [A] Hold BOOT while powering on to force DFU mode for flashing.
[B] When powered and in standby, short-press cycles LED display modes; long-press switches SB-LED/ST-LED. In ST-LED mode, LED1–LED4 are controlled by FC firmware.
RSSI Pads Supported
SmartPort Not supported
Supported FC Firmware Betaflight, INAV, Ardupilot
Firmware Target Name SPEEDYBEEF405V5
Factory Firmware Version Betaflight 4.5.2
Configurator Version Betaflight 10.10.0
Mounting Holes 30.5 × 30.5mm (Ø4mm), side opening
Dimensions 39mm (L) × 39mm (W) × 4.9mm (H)
Weight 8.1g
Product Name SpeedyBee OX32 55A 30.5×30.5 4-in-1 ESC
Default Firmware OX32
Continuous Current 55A (per channel) / 220A (4-in-1)
Maximum Current 70A (per channel) / 280A (4-in-1)
TVS Protective Diode Yes (built-in)
External Capacitor 1000µF Solid Capacitor (included in package)
ESC/Motor Protocol DSHOT300/600
Input Voltage 3-6S LiPo
Power Output VBAT
Current Sensor Supported
ESC Telemetry Supported
Mounting Holes 30.5 × 30.5mm (Ø4mm), side opening
Dimensions 40.9mm (L) × 44.9mm (W) × 8.0mm (H) (incl. heatsink)
Weight 19.1g
ESC Webpage https://ox32.oxbot.com/
Current Meter Note Supported (Scale=27, Offset=-2644)
Thông tin bổ sung
Thương Hiệu

SpeedyBee
Loại FC - ESC

Tháp Mạch Stack 30*30
Vi Xử Lý

F405
Dòng Tải

55A
Size Drone FPV

5inch, 6inch, 7inch

Sản phẩm tương tự

+

Mạch HAKRC F722 40A 2-6S BLS

1,760,000₫
+

Tháp Mạch AxisFlying Argus Pro F722 – 65A Stack

3,600,000₫
+
 Sản phẩm này có nhiều biến thể. Các tùy chọn có thể được chọn trên trang sản phẩm

Tháp Mạch AxisFlying Argus F722 – 55A Stack

1,500,000₫
+

Mạch HAKRC F411 20A Aio 2-4S BLS

1,260,000₫
+
 Sản phẩm này có nhiều biến thể. Các tùy chọn có thể được chọn trên trang sản phẩm

Tháp Mạch Mamba F722 MK4 Mini – F40 128K

2,180,000₫